 |
Sure Klean® 101 Lime Solvent is a concentrated acidic cleaner for dark-colored brick and tile surfaces which are not subject to metallic oxidation. Can be used on colored mortar joints. Safely removes excess mortar and construction dirt. |
| |
|
| Sure Klean 101 |
| Product Code |
SK101 (1 Gallon) |
| Coverage |
Concrete Block: 500-900 sq. ft. / gallon
Concrete: 500-900 sq. ft. / gallon
Fired Clay: 500-900 sq. ft. / gallon
Sandstone: 500-900 sq. ft. / gallon
Slate: 700-900 sq. ft. / gallon |
| Surface Preparation |
Protect people, vehicles, property, metal, painted surfaces, plants and other nonmasonry materials from product, splash, rinse, winddrift and fumes. When working over traffic, clean when traffic is at a minimum. Protect or divert traffic if necessary. Clean masonry before installing windows, doors, finished flooring, metal fixtures, hardware, light fixtures, roofing materials and other nonmasonry items that the cleaner could harm. If already installed, protect with polyethylene before application. Sure Klean®Strippable Masking is appropriate for use with this product to protect windows. Maintain ventilation to avoid buildup of potentially damaging fumes. All caulking and sealant materials should be in place and thoroughly cured before cleaning.
Surface Preparation
New brick and tile surfaces clean most effectively if the cleaning is done within 14-28 days of installation. Mortar and grout smears left on the surface longer result in a more difficult cleandown and may cause undesirable results. Cleaning high-strength mortar/grout within seven days improves results. NOTE: Excessive moisture in the wall contributes to efflorescence and other staining. Always protect open wall cavities from rain during construction. |
| Application |
Before use, read “Preparation” and “Safety Information.”ALWAYS TEST (minimum 4 ft. by 4 ft. area) for suitability and results before overall application. Test each type of masonry and each type of stain. Let test area dry 3 - 7 days before inspection. Test using the following application instructions. Keep the testpanel available for comparison throughout the cleaning project.
Dilutions
Dilute one part product with between 4 and 8 parts clean water, based on test results. Adjust dilution rate according to test results.More porous masonry and high-strength mortar/grout will require stronger solutions. Clean glazed surfaces with the mildest solution possible to avoid harm. Always pour COLD water into empty bucket first, then carefully add product. NEVER USE HOT WATER. Handle in polypropylene buckets only. Acidic materials and fumes attack metal. When calculating the volume of cleaner required for porous, textured surfaces, assume 50 square feet per gallon of prepared cleaner. For dense, smooth surfaces, assume up to 150 square feet per gallon of prepared cleaner. The coverage rate chart assumes an average coverage rate of 100 square feet per gallon of prepared cleaner. Do not alter or mix with chlorine-type bleaches or other chemicals (may release toxic gases). Do not dilute product except as specified on label. Do not use for applications other than specified.
Application Instructions
EXTERIOR APPLICATION
Test thoroughly before cleaning.
1. Prewet a large area with fresh water.
2. Using a densely-packed, soft-fibered masonry washing brush,or low-pressure spray (50 psi maximum), apply the diluted solution freely.
3. Let cleaning solution stay on the wall for 1 - 3 minutes. Don’t let cleaner dry into the masonry. This may leave residue and stains.
4. Immediately reapply cleaning solution and scrape off heavy buildup of excess mortar using a wooden scraper or piece of brick. Take care not to harm the masonry surface.
5. Rinse thoroughly with fresh water, removing all cleaning compound, free sand, loose material and debris. Thorough rinsing is extremely important to ensure that all residues arere moved from the porous masonry.
6. Reapply as required following steps 1 through 5.
Caution: Multiple applications may affect the mortar color. Fresh-water rinse the surfaces below areas being cleaned to prevent streaking. Do not apply Sure Klean® 101 Lime Solvent with pressure spray above 50 psi. This drives the chemicals deep into the surface, making complete rinse difficult. Test spray equipment for compatibility and to avoid discoloration.
INTERIOR APPLICATION
Proper ventilation is necessary. Test thoroughly. Follow preceding preparation and cleaning procedures for exteriors. Rinse thoroughly with fresh water using a sponge or soft-fibered brush. If there isn’t enough water for complete rinsing, use neutralizing rinse following this procedure:
1. Rinse with clear water.
2. Apply neutralizing rinse of 2 ounces baking soda to 1 gallon water.
3. Saturate. Leave solution on surface 3-5 minutes.
4. Apply final rinse of clear water. |
| Clean Up |
Clean tools and equipment using fresh water. |
| Sizes Available |
1 Gallon |
| Locations Available |
Terre Haute, Vincennes, Washington |
| Manufacturer's Website |
|
|
|
